119:-

Lacquer paint

Areas of use
LACQUER PAINT is a high-quality, non-yellowing lacquer paint intended for wood and metal surfaces as well as for woodwork and most substrates both indoors and outdoors. Contains rust inhibitor which makes it suitable for use in rustproofing painting iron. 0.75 l.

Special properties
Gives a full-toned and durable surface with excellent coverage and an even gloss. The adapted viscosity makes it easy to apply on vertical surfaces. Contains active rustproofing substances that give a more basic form of rustproofing. If more than a temporary rustproofing is desired, prime the surface first with rustproofing primer. The metal paint gives an even and hard surface, also making it suitable for use in spray painting of woodwork indoors.

Instructions
The wooden surface must be clean and dry. Wash, rinse and allow it to dry well. Any oil spillage is removed with a solvent. Untreated wood is to be primed with woodworking primer diluted with 10-20 % white spirit. Use filler to even out irregularities. Sand lightly. Carry out paint-rubbing with undiluted woodwork primer, intermediate sanding, paint-rub again and repeat until an even and smooth surface has been achieved. Wipe any dust off. Paint the topcoat at least twice with undiluted lacquer paint with at least 24 hours' drying time between coats. The lacquer paint shall normally not need to be stirred prior to use.

Metal substrates shall be properly cleaned, steel-brushed or sand-blasted. Any oil spillage to be washed off with a solvent. For iron surfaces, first apply a layer of rustproofing primer diluted with 20 % white spirit. Then prime using undiluted primer and top coat then surface with lacquer paint twice. Applied with a brush, lint-free roller or spray after diluting 10–20 % white spirit. It is important to rustproof directly after cleaning, so that corrosion does not get a foothold.

Tips
If not all the contents of the tin are used, replace the lid firmly and then store the tin upside-down. This ensures that any skin that might form will be at the bottom of the tin.

Technical data
Bonding agent: Urethane alkyd
Gloss: 60–70 (gloss) in compliance with SS-184184
15–20 (matt) Density: 1.11 in compliance with SS-184111
Dry matter content: 43 % by volume
Material consumption: 8–12 m²/l
Drying time: 4 hours touch-dry,
24 hours between coats, 48 hours fully cured depending on temperature and air humidity. Viscosity: Viscose.
Fire hazard class: 2 b
Storage/transport: 2 years 8 in unopened packaging.
Ambient painting conditions: Over +4 °C
Dilution/cleaning: white spirit/aliphatic spirit
  • ENAMEL PAINT 0.75L,DK RED GLOS

    ENAMEL PAINT 0.75L,DK RED GLOS

    Art. 36-717
    Dark red
    119:-
    158,67 / L
  • ENAMEL PAINT 0.75L,YELLOW GLOS

    ENAMEL PAINT 0.75L,YELLOW GLOS

    Art. 36-719
    Yellow
    119:-
    158,67 / L
  • ENAMEL PAINT 0.75L,RED GLOSSY

    ENAMEL PAINT 0.75L,RED GLOSSY

    Art. 36-716
    Red
    119:-
    158,67 / L
  • ENAMEL PAINT 0.75L,BLUE GLOSSY

    ENAMEL PAINT 0.75L,BLUE GLOSSY

    Art. 36-722
    Blue
    119:-
    158,67 / L
  • ENAMEL PAINT 0.75L,BLACK GLOSS

    ENAMEL PAINT 0.75L,BLACK GLOSS

    Art. 36-715
    Black
    119:-
    158,67 / L
  • ENAMEL PAINT 0.75L,BLACK MAT

    ENAMEL PAINT 0.75L,BLACK MAT

    Art. 36-714
    Black
    119:-
    158,67 / L
  • ENAMEL PAINT 0.75,GREEN GLOSSY

    ENAMEL PAINT 0.75,GREEN GLOSSY

    Art. 36-720
    Green
    119:-
    158,67 / L
  • ENAMEL PAINT 0.75L,WHITE GLOSS

    ENAMEL PAINT 0.75L,WHITE GLOSS

    Art. 36-713
    White
    119:-
    158,67 / L
  • ENAMEL PAINT 0.75L,WHITE MAT

    ENAMEL PAINT 0.75L,WHITE MAT

    Art. 36-712
    White
    119:-
    158,67 / L
  • ENAMEL PAINT 0.75L,L. GREY GLO

    ENAMEL PAINT 0.75L,L. GREY GLO

    Art. 36-721
    Light grey
    119:-
    158,67 / L
  • ENAMEL PAINT 0.75L,DARK GREY

    ENAMEL PAINT 0.75L,DARK GREY

    Art. 36-480
    Dark grey
    119:-